Phone:  +086-0755-81475061   | E-Mail: kaiao@cn-rp.com
4
BLOG
You are here: Home » News » Industry News » Reaction Injection Molding vs Injection Molding: Cost, Volume and When to Switch

Reaction Injection Molding vs Injection Molding: Cost, Volume and When to Switch

Views: 1     Author: Site Editor     Publish Time: 2026-11-02      Origin: Site

If you are comparing reaction injection molding (RIM) with injection molding for a part in the 100 to 5,000 unit range, the short answer is this: RIM almost always costs less over the life of the program, because its tooling runs 50 to 60% below a comparable injection mold. Above roughly 5,000 units a year, the math flips and injection molding wins on piece price. The exact crossover is not a fixed number — it depends on your part's size, wall thickness, and finishing needs — and this article gives you the formula to calculate it for your own project, plus the four cases where RIM wins regardless of volume.

1. Why "which is cheaper" is the wrong first question

image.png

Buyers usually open with one question: what is the piece price? That is the wrong place to start, because the two processes have completely different cost shapes.

Injection molding asks you to pay a large sum up front for a hardened steel tool, then rewards you with a very low cost per part at volume. Reaction injection molding flips this: the tool is cheap because it runs at low pressure, but each part costs more because it needs trimming, drilling, bonding and painting after it leaves the mold.

So the real question is not "what does one part cost?" It is "what does the entire program cost?" That means the tooling bill plus every piece, across the number of parts you will actually build — not the optimistic five-year forecast, but the number you will realistically order before the product is redesigned.

One shop that runs this calculation weekly puts it plainly: the programs that surprise people are the ones where someone quoted a five-year volume, and the product changed in year two. A steel mold paid for on paper never earns back its cost.

2. The break-even formula, with real numbers

There is a simple way to settle the comparison. Subtract the RIM tooling cost from the injection tooling cost, divide by how much more one RIM part costs, and you get the break-even quantity. Compare that number with your lifetime program volume.

Break-even quantity = (injection tooling cost − RIM tooling cost) ÷ (RIM piece price − injection piece price)

Here is what that looks like with numbers gathered from published industry sources:

Input

RIM

Injection molding

Source basis

Tool cost, medium part

$5,000–$25,000

$30,000–$150,000

Zetar, uprojectspartner

Tool cost, large enclosure

€15,000–€50,000

€80,000–€200,000

Microns Hub

Fill pressure

50–200 psi

5,000–20,000 psi

Covestro; Zetar

Cycle time

2–10 min

10–60 sec

Zetar

Tool life

5,000–20,000 shots

100,000+ shots

uprojectspartner

Sweet spot

50–5,000 units/yr

1,000–1,000,000+ units/yr

uprojectspartner

 

Work one example. If the RIM tool saves $100,000 and each RIM part costs $2 more, break-even is 50,000 parts. If the piece-price gap is only $0.50, break-even drops to 200,000 parts. For a program that will build 2,000 units a year for three years, the steel tool never pays for itself — RIM is the rational choice.

This is why published guidance consistently lands on a band rather than a point: roughly 100 to 5,000 parts a year is RIM territory, with some sources extending the upper edge to 10,000 units before cycle time erodes the advantage.

3. Why a RIM tool costs 50–60% less

image.png

The cost gap is not a quote trick. It comes from physics, and it shows up in three places.

Lower pressure means softer, faster-to-machine tooling. RIM fills a mold at 50 to 200 psi, while thermoplastic injection molding runs more than an order of magnitude higher. An injection tool must be hardened steel to survive the clamp force; a RIM tool can be aluminum, Kirksite, cast epoxy, or even sprayed metal. The Covestro part and mold design guide indexes machined steel at 100%, machined aluminum near 80%, cast aluminum and Kirksite near 60%, sprayed zinc near 40%, and cast epoxy near 30% for prototype work. Softer material machines faster, and tool time is most of what you pay for.

No press tonnage sized to the part. Many RIM molds are free-standing and hand-clamped, holding parts up to about 1,000 lb. There is no giant press to amortize into your quote. Because cavity pressure is low, RIM needs only modest clamping force compared with a thermoplastic injection press sized to the same part's projected area.

Lead time collapses. Aluminum and epoxy RIM tools are routinely ready in about two weeks. At KAIAO, RIM tooling is completed within two weeks, and the process holds single parts up to roughly 85 lb with cavity dimensions around 2000 × 1200 × 1000 mm.

For a deeper breakdown of tool materials and what each one costs, see our companion article on RIM tooling cost.

4. Why the RIM piece price is higher — and where it hides

Honesty matters here, because the higher per-part cost is real. A RIM part comes out of the mold needing more hands than an injection molded part. Trimming flash, drilling, bonding inserts, sanding and painting all happen after demold, and that labor lands in the piece price.

The mold itself is fast — an average RIM cavity fills in about a second and the part demolds in 30 to 60 seconds. The time and cost sit in what follows. Depending on the source, total RIM cycle time runs 2 to 10 minutes versus 10 to 60 seconds for thermoplastic injection molding.

Material is the second driver. RIM polyurethane systems are quoted around €8–15 per kilogram against €3–8 for engineering thermoplastics. Two things soften this: large injection molded parts can waste 20 to 40% of material as runner and sprue scrap, which RIM largely avoids, and structural foam grades let you lower part density to cut chemical cost per shot.

The practical takeaway: get the finishing scope written into the quote. Painting, texture and in-mold coating are line items, not afterthoughts. Our article on RIM Class A surface finishing explains how to specify these so they are priced, not discovered later.

5. Four cases where RIM wins regardless of volume

image.png

Volume is not the only variable. Four situations keep a part in RIM territory even when the annual quantity looks too high.

1. The part is too large for available press capacity. When projected area grows to several square meters, clamp force in injection molding scales with that area and the press becomes the bottleneck. RIM's low cavity pressure means the mold can stay free-standing. Large enclosure panels several feet across are exactly where shopping a steel mold stops making sense.

2. Wall thickness swings widely in one part. RIM tolerates sections from about 0.125 in to over 1 in within the same molding, because cure is driven by chemistry rather than heat conduction through the wall. Thermoplastic injection molding fights sink and flow limits at that range. At KAIAO, wall thickness can vary from 3 to 60 mm in a single part.

3. Components must be encapsulated. Because fill pressure is low, you can place a PCB, sensors, a wire harness, magnets or a metal frame in the cavity without washing it away. This is why low-pressure RIM is standard for medical enclosures with embedded electronics and automotive parts with bonded brackets.

4. One RIM shot replaces an assembly. If a part currently consists of several injection molded pieces plus fasteners and the labor to join them, you are not comparing part to part — you are comparing a molding to an assembly. Run the volume math on the whole assembly, and RIM often wins even at higher quantities.

Each of these exceptions is worth checking before you commit tooling money. For a part that is also being considered against silicone-molded parts, our RIM vs vacuum casting comparison covers the crossover by size and batch.

6. When injection molding is still the right answer

A credible comparison has to say where RIM loses. Stay with injection molding when any of these apply:

· Volume is high. Above roughly 5,000 parts a year for a mid-size part — and above about 25,000 for a smaller one — the short injection cycle overwhelms the tooling saving. Several shops say they will tell you this on the phone rather than let you pay for the wrong tool.

· You need engineering thermoplastics. RIM is fundamentally limited to thermoset systems, primarily polyurethane and polyurea. If the application calls for PEEK, PPS, polycarbonate or polypropylene, RIM cannot deliver the chemistry. This is the single most common reason engineers drop RIM after evaluation.

· You need a Class A surface straight from the mold. As-molded RIM generally shows flow marks, porosity and color variation. Cosmetic quality takes priming, filling and painting. With a polished steel tool, injection molding gets you closer to a cosmetic surface without that step.

· Recyclability is a hard requirement. Thermoset polyurethane cannot be remelted and reground the way thermoplastic scrap can.

Choosing the wrong process is far more expensive than choosing the right one, even if the right answer is not the process we run.

7. What buyers get wrong when comparing quotes

Three mistakes show up repeatedly in sourcing conversations.

Comparing first-year volume instead of lifetime volume. The crossover formula only works if the denominator is the real total. Quote a five-year number, redesign in year two, and the cheap-piece-price argument collapses.

Ignoring who owns the tool. Tool ownership, modification rights and maintenance terms belong in the quote, not in a conversation after payment. A lower tooling number means little if you cannot move or change the mold.

Leaving finishing out of the comparison. A RIM part that needs painting is not the same quote as one that does not. Ask for trimming, texture, color matching and in-mold coating as separate lines so the two processes are compared on equal scope.

8. How to run the math on your own part

You need four inputs: the two tooling quotes, the two piece prices, your realistic lifetime volume, and a written list of finishing operations. Then:

1. Confirm the tool cost gap and the piece-price gap from like-for-like quotes.

2. Divide the gap in tool cost by the gap in piece price to get break-even quantity.

3. Compare break-even with lifetime volume — not annual volume, not year one.

4. Check the four exceptions in Section 5 before accepting the result.

If the part is large, has widely varying walls, carries inserts, or replaces an assembly, the volume answer alone is not enough.

9. Verdict

RIM and injection molding are not competing on the same axis. RIM trades a cheaper tool for a higher piece price; injection molding does the reverse. For a large plastic part in the 100 to 5,000 unit per year band, the cheaper tool usually wins the program. Above that, the shorter cycle takes over — unless the part is very large, has a big wall-thickness swing, needs encapsulation, or consolidates an assembly.

Do the arithmetic with your own quotes before you release tooling. The formula takes minutes; the wrong tool takes months and cannot be undone.

Call to Action (CTA)

Send a sketch or 3D file (STEP, IGES or STL) with your annual quantity and we will run the crossover math against your part before either side commits to tooling. KAIAO builds RIM and injection tooling in-house, holds ISO 9001 and ISO 13485, and returns a DFM review with the quote. Contact kaiao@cn-rp.com or visit our RIM products page.

 

FAQ

Is RIM cheaper than injection molding?

It depends on volume. RIM tooling is typically 50 to 60% less expensive, which makes it cheaper overall for roughly 100 to 5,000 parts a year. Injection molding becomes cheaper above that because its per-part cost is lower.

How much does a RIM mold cost compared with an injection mold?

For a medium-complexity part, published figures put a RIM tool around $5,000–$25,000 versus $30,000–$150,000 for injection molding. Large enclosures run €15,000–€50,000 for RIM against €80,000–€200,000 for a mega-tonnage injection tool.

At what volume does injection molding become cheaper?

For a mid-size part, the crossover is commonly cited around 5,000 units a year, and some sources place it near 10,000. For smaller parts it can be as low as 2,000 to 5,000. Use the break-even formula with your own quotes rather than the general rule.

Can RIM produce parts larger than injection molding can?

Yes. Because cavity pressure stays under about 200 psi, RIM does not need press tonnage sized to the projected area. Parts several square meters in area and up to roughly 1,000 lb are practical, where injection molding would need a very large press.

Why is the RIM piece price higher?

Most of the difference is post-molding labor — trimming, drilling, bonding, sanding and painting — plus a higher material cost per kilogram. The mold fills quickly, but the part needs more work after it demolds.

Can RIM replace engineering plastics such as PEEK or polycarbonate?

No. RIM uses thermoset chemistry, mainly polyurethane and polyurea. If your design requires engineering thermoplastics for heat, chemical resistance or transparency, injection molding is the appropriate process.

Send A Message

SERVICE

RESOURCES

Leave a Message
Send A Message

INDUSTRIES

CONTACTS US

   +086-0755-81475061  / +86 13823544576
  kaiao@cn-rp.com
  Floor 2, Block 9, AoHua Industrial Park, DaLang HuaRong Road, LongHua District, Shenzhen City, Guangdong Province, PRC 518110
Copyright © 2026 Shenzhen Kaiao Mould Technology Co., Ltd. All Rights Reserved  Technical support: Molan Network